Description

Concrete Polishing Guard

DESCRIPTION:

Cement Shine Concrete Polishing Guard is an exclusive amalgamation of micro-polymers and hybrids formulated to cast a tenacious shine and protective impalpable membrane for polished concrete floors. This product was designed with the purpose of providing better stain protection than previously available from industry-standard polishing guards.

Concrete Guard is formulated to provide the ultimate in concrete protection by using both dual-action technology and hybrid polymers. Concrete Guard is environmentally friendly, VOC- compliant, and provides increased stain suspension and resistance against most contaminants found in kitchens, retail food stores, restaurants, malls, garages, warehouses, distribution centers, etc. While originally formulated to be used in conjunction with hardened concrete floor systems, Concrete Guard may also be used anywhere a clear, high-gloss, dual-action concrete protection system is desired. Concrete Guard is designed for use on previously densified and polished surfaces, as well as surfaces that have been previously stained or dyed and sealed.

CSCPG is introduced as an answer to the industry-standard specifications that have failed to address the needs of higher stain protection required in Grocery stores, dining areas, pet service facilities, and those with exposure to common oils. Cement Shine Concrete Polishing Guard is formulated as a protective coating treatment to help resist acidic foods including orange juice, red wine, pickle juice, and other oils and standing waters. Cement Shine Concrete Polishing Guard provides a greater window of opportunity to clean a spill then many available guards. For higher chemical resistance try Cement Shine Concrete Polishing Guard Plus.

SUMMARY DIRECTIONS:

Make sure the concrete floor is clean and dry. Using a Hudson type garden sprayer, squirt product on the floor, and immediately mop the product using a Cement Shine Microfiber mop pad. Apply the product very thin. Thinner is a winner. Do not over apply. Keep wet edge, do not over-mop once the product starts to dry. Depending on temperature and humidity product may take 45 mins or less to dry. The floor can be burnished with a Cement Shine white poly pad once the product is dry. This is not required. For a high gloss, use Cement Shine Hog hair pads on high-speed burnisher, polishing concrete surface. For highest protection apply two thin coats. The product may cover 1100-2000 SF per gallon on the first coat depending on the porosity of the floor.

DIRECTIONS:

A small test patch application is always recommended. The test patch must be done using the same applicator, equipment, surface preparation, application technique, and at the same temperatures, relative humidity, airflow conditions, etc., that will exist at the time of the full-scale application. The surface must be thoroughly clean, dry, and free of anything that will prevent Concrete Guard from bonding properly with the concrete.

Polished Concrete: Concrete Guard may be applied over concrete that has been previously treated with a densifier/hardener.

Existing Concrete: Concrete Guard should be used full strength on existing concrete (no dilution necessary). Concrete must be a minimum of seven days old before applying.

Application Method: Application equipment must be clean, dry, and free of any previously used materials. After initially spraying the product onto the surface, uniformly spread it with a microfiber applicator. The micro-fiber pad should be prewetted with Concrete Guard prior to use, and the product must not be allowed to dry before spreading is complete. Optimum performance is achieved with two uniform coats. The second coat should be applied at a 90° angle to the first coat, only after the first coat is thoroughly dry – typically one hour after application, depending on temperatures and conditions.

NOTE: Keep surface dry for a minimum of 48 hours after application; full stain-blocking ability will not be effective until 72 hours after the final application.

Cleanup: If the product is still wet, the equipment can be cleaned with soap and water. Once dried, the material can be removed with a solvent, such as a xylene or toluene.

MAINTENANCE:

See www.cementshine.com for all Maintenance procedures or use Cement Shine Concrete Daily Cleaner

RECOAT:

Periodic Recoating of the floor is based on the type and volume of traffic, and the floors’ historical maintenance.

DISCLAIMER:

Since Manufacturer has no control over handling, use, or storage; no guarantee express or implied, is offered. The suitability of the product for use shall be solely up to the user. The manufacturer retains the right to the venue.

Cement Shine LLC

9550 Spring Green Blvd Suite 408-125 Katy, TX 77494, USA     832-600-8419

PRECAUTION:
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking. Keep the container tightly closed. Do not breathe mist/vapors/spray. Wash skin thoroughly after handling. Use only outdoors or in a well-ventilated area. Use personal protective equipment as required. KEEP OUT OF REACH OF CHILDREN.

FIRST AID:
IF SWALLOWED: Do NOT induce vomiting. Immediately call a poison center or doctor/physician.

IF ON SKIN: (or hair): Remove/take off immediately all contaminated clothing. Rinse skin with water/shower. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call poison center or doctor/physician IF IN EYE: Rinse cautiously with water for several minutes. Remove contact lenses, if present, and easy to do. Continue rinsing. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. In the case of fire use dry sand, dry chemical,